Dark Current Enable Tool

All things embedded.
*NO FEATURE REQUESTS*

Re: Dark Current Enable Tool

Postby Iliah Borg » Tue Sep 23, 2014 5:20 am

Best regards,
Iliah Borg
http://www.libraw.org
Iliah Borg
 
Posts: 8
Joined: Sun Sep 21, 2014 4:38 am
Been thanked: 2 times

Re: Dark Current Enable Tool

Postby astronomer » Tue Sep 23, 2014 3:24 pm

User avatar
astronomer
Developer
 
Posts: 722
Joined: Fri Apr 06, 2012 10:06 am
Location: US
Been thanked: 293 times

Re: Dark Current Enable Tool

Postby astronomer » Tue Sep 23, 2014 3:31 pm

User avatar
astronomer
Developer
 
Posts: 722
Joined: Fri Apr 06, 2012 10:06 am
Location: US
Been thanked: 293 times

Re: Dark Current Enable Tool

Postby Iliah Borg » Tue Sep 23, 2014 4:24 pm

> From the histogram, the bias level always centered at 600ADU.

Right. Let's see some "mode 3" shots tomorrow. It switches off long exposure noise reduction / median filter.

> we stack many dark frames to get the average dark signal value from each pixel and subtract it from light frame to do the calibration

Sure.
Best regards,
Iliah Borg
http://www.libraw.org
Iliah Borg
 
Posts: 8
Joined: Sun Sep 21, 2014 4:38 am
Been thanked: 2 times

Re: Dark Current Enable Tool

Postby Iliah Borg » Tue Sep 23, 2014 4:29 pm

> Manual lens will disable the dynamic scaling only

And leave WB preconditioning / R/B calibration scaling as it is.

> new lens has much better optical design

I use EL lenses to evaluate in-camera raw processing, and rarely for imaging purposes - unless I need to shoot in UV or IR.
Best regards,
Iliah Borg
http://www.libraw.org
Iliah Borg
 
Posts: 8
Joined: Sun Sep 21, 2014 4:38 am
Been thanked: 2 times

Re: Dark Current Enable Tool

Postby astronomer » Thu Sep 25, 2014 8:49 am

User avatar
astronomer
Developer
 
Posts: 722
Joined: Fri Apr 06, 2012 10:06 am
Location: US
Been thanked: 293 times

Re: Dark Current Enable Tool

Postby Andrew » Wed Oct 01, 2014 9:08 pm

Hi. I am very excited by this post- I use D800 for scientific research. Was the link taken down for this program? I can't seem to find it.
Andrew
 
Posts: 4
Joined: Sat Apr 12, 2014 3:41 pm
Been thanked: 0 time

Re: Dark Current Enable Tool

Postby astronomer » Sun Oct 05, 2014 2:50 pm

User avatar
astronomer
Developer
 
Posts: 722
Joined: Fri Apr 06, 2012 10:06 am
Location: US
Been thanked: 293 times

Re: Dark Current Enable Tool

Postby Andrew » Wed Oct 08, 2014 6:24 pm

Thank you very much for this tool.

Has anyone tested this with using remote control software to control camera over USB? I have been trying with the following procedure but It seems to put the camera in an error state and then it needs to be power cycled to communicate again-

1. run dark current enable tool, leave program open
2. run camera control software
3. camera control software gives error saying the device is busy

Thanks,
Andrew
Andrew
 
Posts: 4
Joined: Sat Apr 12, 2014 3:41 pm
Been thanked: 0 time

Re: Dark Current Enable Tool

Postby astronomer » Thu Oct 09, 2014 11:17 am

User avatar
astronomer
Developer
 
Posts: 722
Joined: Fri Apr 06, 2012 10:06 am
Location: US
Been thanked: 293 times

PreviousNext

Return to Firmware

Who is online

Users browsing this forum: No registered users and 11 guests